Test & Measurement


Reliability and performance are crucial for high-performance test sockets

22 July 2015 Test & Measurement

Given the constant advances and prominence of electronic devices making use of wireless communication, manufacturers of the components and modules used in these applications must carefully test their devices, making a properly configured high-performance test socket a key part of the testing equation.

‘High-performance’ means two things in terms of test sockets: achievement of a substantial number of device insertions before the socket needs replacing; and the display of superb electrical performance. As the frequencies of devices used in wireless applications increase, test sockets must be able to perform at higher frequency levels. Reliability and performance are therefore two key areas of concern when evaluating various test sockets.

Reliability

A socket’s reliability is crucial to help lower the cost for each device tested. Ideally, a socket should require no repair, and operate reliably during its full life cycle. In reality, it will need cleaning, repair or replacement. Cleaning can require a complete breakdown of the test board. Repairing a socket almost always requires test board breakdown, followed by another setup. Socket adjustments, although performed infrequently, use up valuable test time. As a result, throughput is lowered and the cost per device tested is increased.

Temperature can affect socket life and reliability. Each device must be tested under the same conditions in which it will be used, and test temperature extremes can range from -55°C to +150°C. Naturally, sockets that can withstand these temperatures through hundreds of thousands of cycles are more expensive than conventional test or burn-in sockets, but they will pay for themselves through long service life.

Thermal considerations involve continuous service temperature and coefficient of thermal expansion (CTE). Different materials expand at different rates under the same temperature conditions, so the housing material must be flexible enough to accommodate these variations, and tough enough to withstand them.

Occasionally, a socket contact, or the socket itself, must be replaced. This can result from simple wear-and-tear, or from using a socket that’s inadequate for the purpose. In both cases, the situation incurs downtime and cost to effect the repair, and cost of replacement parts.

Performance

The ideal test socket should be electrically ‘transparent;’ that is, its presence will have no effect on the test results. This characteristic can be achieved with a low self-inductance and capacitance between contacts, and the contact’s ability to maintain controlled impedance.

A socket's high-frequency capability is inversely proportional to its contact inductance. High lead inductance values can lead to unwanted oscillations and signal degradation. That’s why package engineers concentrate on developing packages with low lead inductance.

Inductance and capacitance influence the overall impedance value of the socket contacts. Therefore, the test socket’s contact impedance should closely match that of the device package. Impedance mismatches can lead to signal reflections, which can cause signal loss and oscillations.

Impedance is a complex term that defines the resistive and reactive elements of an electrical signal medium, whether it’s a wire or printed circuit board (PCB) microstrip trace. The resistive element is determined by the wire’s resistance and the reactive element is determined by the inductance and capacitance of the PCB microstrip trace. As an electrical signal travels through a trace, its fundamental characteristics change as the impedance changes, and as the signal’s frequency increases, so does its reaction to the change in impedance.

Although it’s relatively easy for board designers to match lead impedances, it’s often difficult for socket manufacturers to do likewise. Most sockets simply do not have any means of impedance control.

Mutual inductance and capacitance characteristics pose other problems. As a signal’s frequency increases, so does its electromagnetic field. If the socket’s design and materials of construction contribute to coupling characteristics, then unwanted electrical cross-talk between these fields will promote the development of oscillations, reduce gain level and increase signal degradation, with a subsequent detrimental effect on performance.

Housings

To investigate how this applies in practice, it’s important to examine two key components of a high-performance test socket: the housing and the contacts.

Polyetherimide is a typical housing material. It is a thermoplastic that displays excellent mechanical, thermal and electrical properties. In production settings, automated device handlers are widely used. It’s important that the housing’s mechanical specifications are close to those of the handler’s plunger mechanism (which is usually made of polyamideimide) because these two parts can come in contact with each insertion of an IC package. Flexural strength is also critical, because of the repeated cycle of pressure and release that occurs when the housing is used as a hard stop to eliminate damage to the device under test.

The continuous service temperature rating for polyetherimide is -60°C to +170°C which exceeds even the strict temperature testing range established for military applications. Ultem’s CTE is very low, which helps maintain close dimensional stability of the housing for IC package alignment, and good co-planarity between the socket and test board.

The dielectric constant and dissipation factor of polyetherimide are 3,15 and 0,0015 respectively, at 1 MHz – respectable numbers for RF applications. These two specifications minimise the socket's mutual conductance, thus reducing cross-talk and leakage currents at high frequencies.

Contacts

The heart of any test socket is its contacts, because they provide signal transmission paths between the device and the test board. Proper signal transmission depends upon proper contact design and implementation.

The Microstrip contact patented by Aries Electronics provides many of the characteristics required by high-performance testing. It provides minimal signal loss in high-bandpass applications and delivers long cycle life (over 500 000 cycles) in automated handler testing. Additionally, it provides a virtually transparent connection between the device under test and the printed circuit board.

During test, the Microstrip contacts lie flat against the PCB microstrip, whereas short contacts and cantilever contacts introduce a significant signal path (2 mm and 20 mm, respectively) to the device under test. The contact is made from 0,178 mm thick, gold-plated proprietary high-service life material, which was developed for its ease of processing and spring strength. Gold plating provides low ohmic contact between the gold-plated test board trace and the contact.

When the Microstrip contact lies flat against the PCM microstrip, it actually becomes part of the transmission line. Both can be designed with the same width, enabling designers to closely match the device’s lead impedance. The transition of the contact into the PCB microstrip leads to extremely low contact self-inductance and very low signal loss in high-frequency applications.

Less than 24 grams of contact force per contact is required with a 0,5 mm lead pitch device (0,304 mm wide contacts), and a built-in wiping action is featured to remove surface debris, solder build-up and other possibly contaminated materials.



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Analyser and voltmeter capability added to portable instruments
Tamashi Technology Investments Test & Measurement
Anritsu Company had added Vector Network Analyzer and Vector Voltmeter measurements to their industry standard Site Master instruments.

Read more...
Marktech’s latest LEDs and photodiodes
NuVision Electronics Test & Measurement
Designed for precision sensing and emission tasks, Marktech’s optoelectronic lineup serves medical, industrial, aerospace, and environmental markets.

Read more...
MEMS air quality sensor
Future Electronics Test & Measurement
Bosch Sensortec’s BME690 is the latest-generation gas sensor that combines advanced monitoring capabilities with innovative artificial intelligence functionality.

Read more...
Telemetry retrofit for sustainable resource management
CST Electronics Test & Measurement
AquaMeter is a cost-effective secure telemetry retrofit that can easily be added to hundreds of millions of legacy mechanical water meters.

Read more...
True-RMS clamp meter measures 2500 A
Comtest Test & Measurement
The Fluke 376 FC True-RMS Clamp Meter with iFlex is the most advanced troubleshooting tool for industrial and commercial electricians.

Read more...
Latest wireless barcode scanner
Brady Corporation Test & Measurement
Brady has launched its new barcode scanner, the CR2100, which is a wireless handheld scanner utilising Bluetooth 5 LE for communication with a host device.

Read more...
hybridNETBOX instrumentation platform
Vepac Electronics Test & Measurement
The hybridNETBOX from Spectrum Instrumentation is an innovative instrumentation platform that combines a multi-channel arbitrary waveform generator (AWG) and a digitiser in a single portable unit.

Read more...
14-bit AWG at 20 GS/s
Vepac Electronics Test & Measurement
The Arb Rider AWG-7000 is the world’s fastest 14-bit Arbitrary Waveform Generator, featuring a 20 GS/s real time update rate and 14-bit vertical resolution.

Read more...
Additions to APD5000 series oscilloscopes
Osiris Technical Systems Test & Measurement
Each unit is equipped with an integrated CAT II digital multimeter, three programmable power supplies, a dedicated trigger line, and an arbitrary waveform generator.

Read more...
Handheld RTSA up to 9,5 GHz
Vepac Electronics Test & Measurement
The PXE-90 implements an FFT engine on the built-in FPGA and support frame compression with trace detection while ensuring no missing samples between FFT frames.

Read more...









While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved