Op-amp with over-voltage protection
29 October 2008
Analogue, Mixed Signal, LSI
New from Analog Devices is a highly integrated precision operational amplifier with on-chip over-voltage protection circuitry. The ADA4091-2 provides industrial equipment designers with a reliable, accurate analog input solution.
Industrial amplifiers are subject to fault voltages from a variety of sources, including electromagnetic interference, damaged cabling, lightning strikes and other disturbances on the power grid, incorrect hookups to other system components and power-line surges when power to the system is restored after routine service or equipment upgrades. Such over-voltage conditions can cause phase inversion or damage the amplifier and other circuitry, resulting in system lock-up or outright failure.
The ADA4091-2’s performance is fully specified, including the device’s on-chip over-voltage circuitry. This simplifies equipment design and error analysis and results in more consistent output readings in industrial process controls, battery-powered instrumentation, power supply control and protection systems and remote sensors.
The 1,5 MHz op-amp features 350 μA per channel supply current, a 0,5 V/μs slew rate, and offset voltage of 500 μV. The 36 V device protects up to 12 V above and below the supply rails at ±15 V and 25 V above and below the supply rails at ±5 V.
Further reading:
A new era in modular I/O solutions
Rugged Interconnect Technologies
Analogue, Mixed Signal, LSI
Aerospace and defence system designers are demanding scalable and high-performance I/O solutions and while traditional mezzanine standards have proven reliable, they often fall short of meeting modern bandwidth, size, and flexibility requirements.
Read more...
High voltage instrument op-amp
iCorp Technologies
Analogue, Mixed Signal, LSI
The SGM621B is a high accuracy, high voltage instrumentation amplifier, which is designed to set any gain from 1 to 10 000 with one external resistor.
Read more...
High-speed SAR ADC simplifies design
Altron Arrow
Analogue, Mixed Signal, LSI
The ADI AD4080 simplifies data converter integration by integrating a low drift reference buffer, low dropout regulators and a 16K result data FIFO buffer.
Read more...
2-wire quad voltage output DAC
Altron Arrow
Analogue, Mixed Signal, LSI
The DAC has a 2-wire serial interface that operates at clock rates up to 400 kHz, and this interface is SMBus compatible, allowing multiple devices to be placed on the same bus.
Read more...
Dual-channel ADC for RF applications
RFiber Solutions
Analogue, Mixed Signal, LSI
The ARF0471 from Advanced RF is a dual-channel, 14-bit, 3 GSPS ADC, which features an on-chip buffer and sample-and-hold circuit.
Read more...
Infineon launches Edge Ai software solution
Altron Arrow
Analogue, Mixed Signal, LSI
Infineon has introduced DEEPCRAFT, a new software solution category brand for Edge AI and machine learning, after the company recognised the huge potential of Edge AI for the market.
Read more...
16-bit voltage output denseDAC
Altron Arrow
Analogue, Mixed Signal, LSI
The AD5766 uses a versatile four-wire serial interface that operates at clock rates of up to 50 MHz for write mode, and is compatible with SPI, QSPI, MICROWIRE, and DSP interface standards.
Read more...
AFE enables the software-defined factory
Avnet Silica
Analogue, Mixed Signal, LSI
With its software configurable analogue inputs, where each input can be configured for voltage, current, resistance, or temperature, NXP’s N-AFE enables a new level of flexibility.
Read more...
Precision voltage reference
Altron Arrow
Analogue, Mixed Signal, LSI
The ADR1001 is a fully integrated, ultra-low drift, buried Zener precision voltage reference solution in a single chip.
Read more...
Microphones enable low-power always-on state
Avnet Abacus
Analogue, Mixed Signal, LSI
TDK Corporation has announced its InvenSense SmartSound T5848 I2S microphones to enable intelligent keyword, voice command, and sound detection at ultra-low power.
Read more...
printer friendly version