5 GHz differential amplifier
23 June 2010
Analogue, Mixed Signal, LSI
Analog Devices has introduced a 5 GHz differential amplifier able to drive ADC (analog-to-digital converter) signals from DC to 1 GHz at low power. The ADA4960-1 is a low-distortion, high-speed differential amplifier effective for a wide variety of high-speed ADCs with 10-bit linearity to 500 MHz and 8-bit linearity up to 1 GHz.
The differential amplifier consumes just 60 mA of quiescent current when operating up to 1 GHz. It features an 8700 V/μs slew rate (AV = 6 dB, 2 V step) and wideband, low-distortion performance for frequencies up to and beyond 1 GHz, which make it effective for RF (radio frequency) and IF (immediate frequency) wired communications applications in industrial and instrumentation, defence electronics and aerospace designs. The user accessible gain adjust and bandwidth extension features allow configuration of the ADA4960-1 for line driver and channel equalisation applications.
The ADA4960-1’s gain is adjustable by a single resistor between 0 and 18 dB. It converts a differential or single-ended input to a differential output and operates from a 5 V supply. Settling time to 1% is 1 ns and overdrive recovery is 10 ns.
Further reading:
Infineon launches Edge Ai software solution
Altron Arrow
Analogue, Mixed Signal, LSI
Infineon has introduced DEEPCRAFT, a new software solution category brand for Edge AI and machine learning, after the company recognised the huge potential of Edge AI for the market.
Read more...
16-bit voltage output denseDAC
Altron Arrow
Analogue, Mixed Signal, LSI
The AD5766 uses a versatile four-wire serial interface that operates at clock rates of up to 50 MHz for write mode, and is compatible with SPI, QSPI, MICROWIRE, and DSP interface standards.
Read more...
AFE enables the software-defined factory
Avnet Silica
Analogue, Mixed Signal, LSI
With its software configurable analogue inputs, where each input can be configured for voltage, current, resistance, or temperature, NXP’s N-AFE enables a new level of flexibility.
Read more...
Precision voltage reference
Altron Arrow
Analogue, Mixed Signal, LSI
The ADR1001 is a fully integrated, ultra-low drift, buried Zener precision voltage reference solution in a single chip.
Read more...
Microphones enable low-power always-on state
Avnet Abacus
Analogue, Mixed Signal, LSI
TDK Corporation has announced its InvenSense SmartSound T5848 I2S microphones to enable intelligent keyword, voice command, and sound detection at ultra-low power.
Read more...
Low power, low-noise amplifier
Altron Arrow
Analogue, Mixed Signal, LSI
The ADL8141 is a low power consumption, low-noise amplifier that operates from 14 to 24 GHz, and draws a supply current of 25 mA from a 2 V supply.
Read more...
QLC Flash memory with the latest BiCS technology
EBV Electrolink
Analogue, Mixed Signal, LSI
KIOXIA has implemented the groundbreaking CBA (CMOS directly Bonded to Array) technology, which enables the creation of higher density devices and an industry-leading interface speed of 3,6nbsp;Gbps.
Read more...
Precision op-amp
Altron Arrow
Analogue, Mixed Signal, LSI
The ADA4099-1 and ADA4099-2 are single/dual robust, precision, rail-to-rail input/output operational amplifiers with inputs that operate from -VS to +VS and beyond, which is referred to as Over-The-Top.
Read more...
Using linear regulators as a filter
Altron Arrow
Editor's Choice Analogue, Mixed Signal, LSI
Different circuits can be used to filter a supply voltage, and this article explains the main differences between using an LC filter and a linear regulator for filtering.
Read more...
High-speed PIN diode
Altron Arrow
Analogue, Mixed Signal, LSI
Vishay’s new high-speed Silicon PIN diode is able to detect both visible and near infra-red radiation over a wide spectrum range from 350 to 1100 nm.
Read more...
printer friendly version