Test & Measurement


Handheld Ethernet analyser

31 March 2010 Test & Measurement

Exfo has launched the ETS-1000 Ethernet Analyser, which allows reliable turn-up and installation of carrier-grade Ethernet services over metro networks. Its focused feature set delivers specific functionality and ease-of-use required by field technicians to meet increasingly demanding Ethernet network testing and compliance measurements.

The ETS-1000 is a compact and feature-rich 10 M to 1 GigE test unit, supporting two independent test ports. Technicians can transmit up to layer-4 traffic, with fully configurable virtual local area networks (VLAN), multiprotocol label switching (MPLS) and quality of service (QoS) parameters. The unit supports all of today’s necessary Ethernet/IP field testing capabilities including RFC 2544, bit-error rate, packet jitter as well as multistream generation and analysis.

Also introduced was the ETS-1000L, a dedicated handheld Ethernet loopback device that supports simple user configuration for full wire-speed testing, from Layer 1 through 4. Both the ETS-1000 and ETS-1000L are fully interoperable with all Exfo Ethernet products.

For more information contact Chris Nel, Lambda Test Equipment, +27 (0)12 349 1341, [email protected], www.lambdatest.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

60 MHz 16-bit AWG
Vepac Electronics Test & Measurement
Siglent’s SDG1000X Plus series function/arbitrary waveform generator offers a maximum output frequency of 60 MHz, 16-bit vertical resolution, 1 GSa/s sampling rate, and 8 Mpts arbitrary waveform length.

Read more...
AC programmable power
Accutronics Test & Measurement
TDK Corporation has announced the introduction of the TDK-Lambda brand GENESYS AC and GENESYS AC PRO series of 2 kVA and 3 kVA rated programmable AC power sources.

Read more...
QA introduces large chisel tip style probes
Techmet Test & Measurement
The two new probes have a larger diameter to provide better contact reliability.

Read more...
Best practices for assuring successful PoE device deployment
Lambda Test Power Electronics / Power Management
Looking at the challenges of a typical IoT rollout, the biggest hurdle usually isn’t how to connect IoT devices to the LAN, but instead, how to get power cheaply and reliably to the device.

Read more...
Digital PSU with four variable outputs
Vepac Electronics Test & Measurement
The PeakTech 6215 is a laboratory power supply with four separate voltage outputs, each one infinitely variable using the rotary controls on the front of the unit.

Read more...
High-voltage insulation resistance testers
Comtest Test & Measurement
Two new high-voltage insulation resistance testers, from Fluke, deliver accuracy and speed in industrial and solar PV applications.

Read more...
Digital accelerometer for high dynamics applications
RS South Africa Test & Measurement
TDK extends its Tronics portfolio with the AXO314, a high-performance digital MEMS accelerometer with ±14 g input range for industrial applications operating under shock and vibration.

Read more...
Acceleration sensors for wearables
Future Electronics Test & Measurement
Bosch Sensortec has introduced two new acceleration sensors, the BMA530 and BMA580, both offered in a compact size of only 1,2 x 0,8 x 0,55 mm.

Read more...
Accurate laser measurement
Avnet Silica Test & Measurement
Online Teaser: Panasonic Industry’s laser sensor has a resolution of up to 0,5 µm, a linearity of ±0,05% FS, and a high-speed sampling of 100 µs.

Read more...
Handheld analyser with wide frequency range
Vepac Electronics Test & Measurement
The PXN-400 from Harogic is a handheld spectrum analyser that covers a frequency range of 9 kHz to 40 GHz, with an analytical bandwidth of 100 MHz.

Read more...