RS485 transceivers need no termination resistors

12 July 2006 Analogue, Mixed Signal, LSI

Linear Technology has introduced the LTC2859 and LTC2861, half-duplex and full-duplex RS485 transceivers with switchable, integrated termination.

Traditional RS485 networks require 120 Ω termination resistors to be installed by the end-user based on the physical layout of the twisted-pair wires and the placement of the nodes. As the bus is extended, the termination must be changed again by the end-user. Switching the integrated termination in the LTC2859/LTC2861 on, or off, under software control allows the proper nodes to be terminated without the end-user's physical intervention.

In addition to the innovative termination capacity, the LTC2859/61 offer advanced transceiver features for industrial, medical and automotive applications. A slew rate control pin allows datarates up to 20 Mbps or a low-EMI mode at 250 Kbps. The bus pin protection exceeds ±15 kV for ESD strikes (human body model). The receiver input impedance allows up to 256 nodes on a single bus.

Further reading:

A new era in modular I/O solutions
Rugged Interconnect Technologies Analogue, Mixed Signal, LSI
Aerospace and defence system designers are demanding scalable and high-performance I/O solutions and while traditional mezzanine standards have proven reliable, they often fall short of meeting modern bandwidth, size, and flexibility requirements.

Read more...

---

High voltage instrument op-amp
iCorp Technologies Analogue, Mixed Signal, LSI
The SGM621B is a high accuracy, high voltage instrumentation amplifier, which is designed to set any gain from 1 to 10 000 with one external resistor.

Read more...

---

High-speed SAR ADC simplifies design
Altron Arrow Analogue, Mixed Signal, LSI
The ADI AD4080 simplifies data converter integration by integrating a low drift reference buffer, low dropout regulators and a 16K result data FIFO buffer.

Read more...

---

2-wire quad voltage output DAC
Altron Arrow Analogue, Mixed Signal, LSI
The DAC has a 2-wire serial interface that operates at clock rates up to 400 kHz, and this interface is SMBus compatible, allowing multiple devices to be placed on the same bus.

Read more...

---

Dual-channel ADC for RF applications
RFiber Solutions Analogue, Mixed Signal, LSI
The ARF0471 from Advanced RF is a dual-channel, 14-bit, 3 GSPS ADC, which features an on-chip buffer and sample-and-hold circuit.

Read more...

---

Infineon launches Edge Ai software solution
Altron Arrow Analogue, Mixed Signal, LSI
Infineon has introduced DEEPCRAFT, a new software solution category brand for Edge AI and machine learning, after the company recognised the huge potential of Edge AI for the market.

Read more...

---

16-bit voltage output denseDAC
Altron Arrow Analogue, Mixed Signal, LSI
The AD5766 uses a versatile four-wire serial interface that operates at clock rates of up to 50 MHz for write mode, and is compatible with SPI, QSPI, MICROWIRE, and DSP interface standards.

Read more...

---

AFE enables the software-defined factory
Avnet Silica Analogue, Mixed Signal, LSI
With its software configurable analogue inputs, where each input can be configured for voltage, current, resistance, or temperature, NXP’s N-AFE enables a new level of flexibility.

Read more...

---

Precision voltage reference
Altron Arrow Analogue, Mixed Signal, LSI
The ADR1001 is a fully integrated, ultra-low drift, buried Zener precision voltage reference solution in a single chip.

Read more...

---

Microphones enable low-power always-on state
Avnet Abacus Analogue, Mixed Signal, LSI
TDK Corporation has announced its InvenSense SmartSound T5848 I2S microphones to enable intelligent keyword, voice command, and sound detection at ultra-low power.

Read more...

---