STMicroelectronics recently introduced the new STTS75, a high-precision digital CMOS temperature sensor IC with a sigma-delta temperature-to-digital converter and an I²C-compatible serial digital interface. It is targeted for general applications such as electronics equipment, system thermal management and industrial controllers. With excellent power saving features and a small package, it is well suited to handheld devices.
The device contains a band-gap temperature sensor and programmable 9- to 12-bit ADC which monitors and digitises the temperature to a resolution up to 0,0625°C. The part is accurate to +3°C over the full temperature measurement range of -55°C to 125°C, with +2°C accuracy in the -25°C to +100°C range.
The on-board sigma-delta analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in °C; for Fahrenheit applications a lookup table or conversion routine is required.
The STTS75 is factory-calibrated and requires no external components to measure temperature. The power-up defaults permit stand-alone operation as a thermostat. A dual purpose event pin operates as an interrupt or comparator/thermostat output. The power saving one-shot mode can be used when the part is in shutdown to perform a single temperature conversion.
The IC has a simple 2-wire I²C-compatible digital serial interface which allows the user to access the data in the temperature register at any time. It communicates via the serial interface with a master controller which operates at speeds up to 400 kHz. Three pins are available for address selection, and enable the user to connect up to eight devices on the same bus without address conflict. In addition, the serial interface gives the user easy access to all registers to customise operation of the device.
The STTS75 is specified to operate at supply voltages from 2,7 V to 5,5 V; operating at 3,3 V, the supply current is typically 75 μA. It is available in SO-8 and MSOP8 (TSSOP8) packages.
EMC limits and levels Altron Arrow
Editor's Choice Circuit & System Protection
As soon as electronics and electrical systems started interfering with each other, the world had to come to some consensus. Considering physics is universal and does not care about what country electrical/electronic products are used in, it should be the same everywhere, right? It is nearly there, but not quite.
Read more...Introducing STM32CubeMX2 Altron Arrow
Design Automation
STMicroelectronics has launched STM32CubeMX2, a new evolution of its popular configuration and code generation tool for STM32 microcontrollers.
Read more...Next-gen SPE Altron Arrow
Telecoms, Datacoms, Wireless, IoT
Next-generation 100/1000BASE-T1 Single Pair Ethernet PHYs integrate MACsec security, time sensitive networking, and functional safety.
Read more...Industrial vibration sensing simplified Altron Arrow
Analogue, Mixed Signal, LSI
The IIS3DWBG1 from STMicroelectronics is a high performance, three-axis digital vibration sensor engineered for demanding industrial applications where accurate motion monitoring is essential.
Read more...Safety relay for explosive areas IOT Electronics
Circuit & System Protection
Phoenix Contact has expanded its safety portfolio with the new PSR-MC35-EXI safety relay module, specifically engineered for use in potentially explosive environments.
Read more...Cost-effective microcontroller series Altron Arrow
DSP, Micros & Memory
The STM32C5 series from STMicroelectronics delivers an excellent balance of performance, efficiency, and affordability for embedded designs that require more capability without increasing bill of materials cost.
Read more...Understanding two key tools for cleaner serial data Altron Arrow
Editor's Choice Analogue, Mixed Signal, LSI
Understanding how pre-emphasis and equalisation works, and when to use one over the other, is critical when designing reliable high-speed systems.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version